Vanishing Lubricant, Vanishing Oil-and Evaporative lubricant for Medium to Heavy Duty Metal working
Engineered exclusively for Aluminum, Copper, Copper alloys, Copper/Brass and Ferrous metals
INTRODUCTION:
Evap-Lube_6460 is a premium quality ,light to medium duty solvent based VANISHING OIL . Evap-Lube 6460 evaporative lubricant is specially engineered to be used for press or roll forming both ferrous and non ferrous metals, vanishing lubricant ant 6460 is designed for applications where an extremely thin residue is acceptable . It leaves an imperceptible film that allows a clean die release of thin(0.001 to 0.250) sheet or roll stock. Used for stranding aluminum wire. Contains an anti wear additive to increase die life.
It is a MEDIUM DUTY solvent based Vanishing Lubricant designed for those applications wherein minimal oil film is permissible. This product leaves a thin imperceptible film of lubricant that facilitates a clean die release of thin sheet or roll stock. Depending upon the temperature ,air circulation, and humidity evap-lube vanishing oil dries The carrier generally dries in one to four hours. Normally, cleaning is not required after using vanishing lubricant. 6460 vanishing oil reduces or eliminates most forming cleaning or degreasing prior to plating, painting .assembly or shipping.
Vanishing oil 6460 will virtually disappear - at pre-determined intervals - thus completely eliminating need for any further cleaning, degreasing, buffing or polishing prior to shipping in many operations.6460 specifically formulated for use in roll forming and press operations on pre finished and other specialty metals.6460 is a heavy duty grade in-tended for use in severe applications. It will provide better finish when forming heavier gauge metals or tougher alloys. 6460 is recommended for galvanized aluminum strip.
Evap-Lube 6460 is designed for use where a “vanishing Lubricant” is required. 6460 is a premium quality, high performance, clear, low viscosity metal working fluid. 6460 evaporates readily leaving little or no residual oils for optimum cleanliness during metal working operation, while still providing excellent release properties.
6460’s prompt evaporation characteristics results in the manufacture of clean components, which will readily accept welds, allow for adhesion of paint to processed parts and leave virtually no residue to react with other processing chemicals.
6460contains select additives to provide optimum lubricity during metal stamping and forming, resulting in extended die life. The product formulation obtains the important balance of proper lubrication during metalworking, yet “vanishes” from parts in minimal time to avoid delays in the manufacturing process, and minimizing the need for manual cleaning of components. 6460is non-corrosive and non-staining to aluminum, copper, steel and their alloys.
Vanishing oil 6460should be used in stamping operations to keep the tools cool and prevent wear.
Suitable for ferrous and non ferrous metals
Ideal where rapid drying is required
Where surfaces are painted with oil paints
Burns clean in annealing ovens
FEATURES AND ADVANTAGES :
FEATURES
ADVANTAGES
Excellent cooling
and lubricating
Acid & alkali stable
Non-corrosive to aluminum, copper and other non-ferrous metals and ferrous metals.
Environmentally friendly
Evaporates rapidly. Leaves virtually no residue and No Odor.
High Flash Point
Reduced toll wear and give excellent part finish.
Easily cleaned by acid or alkaline cleaner.
Brightening not needed after cleaning.
Waste disposal does not require special reagents.
99% plus Volatile. Minimizes manual parts clean up. Easier to remove after forming operation.
Reduction of Fire risk with minimum dry times
APPLICATION :
6460 is designed primarily for use in light to light to moderate duty stamping and forming operations of ferrous and aluminum, copper and other non-ferrous metals, while still finding application in some light duty operations with ferrous metals. Its unique ability to provide “thin film” lubrication, then evaporate quickly leaving no residue, makes 6460an excellent choice for applications calling for the use of a “vanishing oil”. 6460can be applied by spraying or roller coating. 6460should always be used as received.
Vanishing oil 6460can be applied straight by spraying, dipping, brushing, flooding or roller coating methods. Caution should be taken when sprayed to not exceed the permissible exposure limits to oil mist.
TYPICAL USES :
Evap-Lube_6460 Can be used for Laminating ,blanking, light duty forming, radiator tank, header and fin forming, perforating, coining and other operations such as parts assembly where a residue free surface is required. Vanishing lubricant EvalplUBE_6460 can also be used on pre-coated stock.
Evap-Lube_6460 is used as received.
Note: 6460should be stored at temperatures between 65°F and 90°F to preserve its integrity. However, if residue on parts is going to be further dried in an oven, operating temperatures should be kept below 250°F to avoid decomposition.
Caution: Product contains solvent. Use mechanical ventilation and guard against open flames or other ignition sources.
Typical physical and chemical properties
Test
Test Method
Results
Specific Gravity @ 60°F
ASTM D-1298
0.895
Pensky-Martens Closed Cup Flash Point, °F(°C)
ASTM-D-93
125°F (52°C)
Cloud Point , °F(°C)
ASTM-D-2500
45°F (7°C)
Color, Saybolt (min)
ASTM-D-156
+25
Copper Corrosion 3 hr. @ 212 °F
ASTM-D-130 1A
Pass
Contains an anti wear additive to increase die life
TESTIMONIAL :
"Hello Walter, I would like to get some of this product to try. I have a job coming up that with about 14,000 lineal feet of bare galvanized. I need to get enough to do that at least. Thanks Craig"
"We used about 20 gallons on coils we ran, the product worked great. Thanks for your help, we'll order more from you in the future Thanks Craig"
B. I recently ordered a 1 gallon sample of
your Evap-Lube 6460 and it is exactly what I am
looking for. It works great for us. I had a
couple of questions regarding the product:
1) What are the quantities that I can order Evap-Lube
6460 in and what are the corresponding prices?
2) What are the HMIS ratings are for the
product? I did not see the ratings on the MSDS
sheet.
If we continue to use the product, we could
potentially use upwards of 1000 gallons per
year.
Note: The information presented herein is our interpretation of certain test results and field experience to date. The information is not to be taken as warranty or representation for which we assume legal responsibility, nor as permission or recommendation to practice any patented invention without a license. It is offered solely for your consideration, investigation and verification.
